Electric Power Services

• Controller upgrades
• Fuel Polishing
• Voltage Regulator upgrades

• Clean, dip, bake & test
• Rotor Rewind
• Stator Rewind
• Replacement of wear components
• Harsh environment coating
• Pitch change
• Voltage change
• Failure Analysis

• Cat Connect Remote Monitoring module installed on equipment
• Monitored by Louisiana Cat Product Support Team
• Accessible via internet using my.cat.com
• Email and text message alerts
• Connected via Cellular Signal

• Clean Oil Suction Screen
• Clean, Inspect, & Pressure Test Aftercooler Core
• Install new Fuel Injectors
• Inspect Engine Wiring Harness
• Inspect Rocker Arms
• Replace Cylinder Head Assemblies
• Inspect / Replace Fuel Press Reg Valve
• Inspect / Replace Pushrods
• Inspect / Replace Spacer Plates

• Clean Oil Suction Screen
• Replace Aftercooler Core
• Replace Fuel Transfer Pump
• Inspect Cam Shaft
• Inspect Cylinder Block
• Inspect Cam Vib Damper
• Inspect Flywheel
• Inspect Front Gear Train
• Inspect Fuel System Linkage
• Inspect/Rebuild Rocker Arms
• Replace Con Rods
• Replace Cylinder Heads
• Inspect Rear Gear Train
• Replace Fuel Priming Pump
• Replace Oil Cooler
• Replace Pistons
• Replace Cam lifters
• Replace Crank Shaft
• Replace liners
• Replace Wiring Harness
• Replace Fuel Reg Valve
• Replace Pistons
• Replace Pushrods
• Replace Spacer Plates
• Replace Cam Shaft Bearings
• Replace Con Rod Bearings
• Replace Crankshaft Seals
• Replace Crankshaft Thrust Plates
• Replace Fuel Injectors
• Replace Gear Train Bushings
• Replace Main Bearings
• Replace Piston Rings
• Replace Exhaust Seals and Bellows
• Replace Air Man Seals
• Replace Air Man Gaskets
• Replace Engine Mounts
• Replace Crank Shaft Seals

Level 1 PM – 50+ Multipoint TA1 Inspection

• Inspect & Adjust Belts
• Inspect Actuator Control Linkage
• Check Engine Mounts
• Inspect Starting Motor
• Take Fluid Samples – Oil, Fuel, and Coolant
• Inspect Fan Drive Bearing
• Inspect Hoses, and Clamps
• Verify All Fluid Levels
• Inspect Water Pump
• Pull Product Status Report (If applicable)
• Check Air Filter & Exhaust System
• Inspect Turbo Charger
• Inspect Exhaust System
• Start Unit for Exercising
• Check Battery Voltage & Charge Rate
• Inspect Generator for Oil & Dirt Buildup
• Inspect Crankshaft Vibration Dampener

Level 2 PM

• Includes everything in the PM1 plus:
• Change Engine Oil, Oil Filters, and Fuel Filters
• Drain crankcase fumes disposal filter
• Lubricate fan drive bearing & Actuator control linkage
• Check rotating rectifier
• Check engine protective devices
• Inspect air filter element

Level 3 PM – Cooling System

• Replace Fan Drive Belts
• Replace Accessory Drive Belts
• Check and adjust belt tension
• Replace Coolant Temperature Regulator(s)
• Replace Hoses
• Drain and Flush Coolant System
• Change Cooling System Coolant

• Resistive testing
• Resistive/Reactive Testing
• Testing at any voltage range from 240V single phase up to 15kV
• Louisiana Cat has a fully capable fleet of load bank equipment for testing small or large generators.
• We can provide testing procedures compliant to NFPA110, or customize to meet your specific needs.

• Valve Bridge Check and Adjustment, 2 Bridges per Cylinder
• Valve Lash Check and Adjustment (if necessary)
• Valve Recession Measurements (if necessary)

• PLC & touchscreen modernizations
• Protection relay upgrades
• Sequence of operations
• Troubleshooting and repairs
• Electrical testing up to 15 KV

Preventive Maintenance

• Cleaning of cable and control sections
• Mechanical and visual checks of wiring, cables, bus bars, circuit breakers, surge arrestors, and transformers
• Mechanical, visual and operational checks of circuit breakers
• Sequence of operations verification

• Valve lash adjustments & Valve recession measurements for head wear
• Coolant System flush
• Radiator and coolant system reconditioning and replacements
• Fuel system troubleshooting and repairs